Tenor

Installation Quick-mounted surface installation with easy snap-on bracket that also serves as marking template.

Connection Rear power cable connection with double wire holder. Rear wire knock-out for armoured cable installation.240V, 60 cycles with armoured cable complete with junction box cover and wire connector supplied with heater. Installation requires a wall box (not included).

Installation height 4 in.

Cleareances
Front: 30 in Sides: 6 in Above: 6 in

Note 3-conductor cable or 2-conductor cable with a third wire shoud be used if unit is to be linked with the Convectair Programmer module (7392 FP).

Total capacity (1000, 1500, 2000 W)
Radiant heat Smoked glass radiant panel with enamelled silver heating circuit.
Convection X-shaped, monoblock element made of surface-treated extruded aluminum.

Thermal protection Automatic reset overheat protection with warning lights.

Electronic thermostat Built-in electronic proportional-action thermostat ultraprecise to 1/5ºF.

Programmer Control panel designed to accept the 7392 Programmer module.

Location Located on top right hand side of the unit with see-through lockable protective cover.

Dial 1 Thermostat control dial can be locked.
Dial 2 Economy adjustment dial (setback can be set between 4ºF and 13ºF below the Comfort setting).

Mode-function selector 5-mode-function selector with indicator light:

• Off;
• Comfort;
• Economy;
• Frost protection (45ºF);
• Program (automatic setback when connected to the Convectair Programmer – see technical specifications for catalogue number 7392).

Indicator light Heating indicator light.

Steel construction with polyester/epoxy anti-rust powder coating.

Cabinet Bottom-mounted protective pan and built-in side wire covers.

Louvres Front-louvered air outlet that hides the unit interior and directs heat towards the center of the room.

Color CB = Sepia Black

For even heat distribution
Natural convection operates on a key principle of physics: hot air rises and cold air falls. When cold air at floor level comes into contact with the X-shaped monoblock heating element, it becomes warm. This element offers exceptional heat conductivity. Each Convectair using natural convection heating therefore transfers as much heat possible to the greatest volume of air.

Thanks to a chimney effect, this warm air rises and is projected through the slanted grille slats toward the centre of the room. Air from the entire room follows in a completely silent, gentle flow. The result is a stable, even temperature. Equipped with precise electronic thermostats, natural convection heaters are the solution of choice for rooms where constant, even comfort is required.

For palpable heat
Radiant units directly heat bodies and objects, producing a caressing warmth similar to the feel of the sun's rays. They create a comforting hot spot, yet evenly distribute heat at the same time. Some radiant units are made for bathrooms while others are ideal in living areas. Gentle radiant heaters are preferred by those who seek an extra “warm comfort”. 

Convectair natural convection heaters do not dry out the air in a room. Since they operate without a fan and the element never heats to red-hot, any particles that are naturally suspended in the air do not burn.
The result: the air stays healthy and the humidity rate remains balanced.  

A Convectair maintains the selected temperature without allowing major fluctuations. Thanks to the electronic thermostat, sensitive to within 1/10 °C (1/5 °F), the room’s occupants can go about their business for as long as they like, in a steadily warm environment without fiddling with the thermostat, oblivious to changes in the outside temperature.

Are you looking for noiseless heating? Whether the model you choose has the X-shaped convection element or a radiant heating surface, Convectair's convection and radiant heaters are designed to work in total silence. You won’t have to put up with the crackling of distorted metal, the bursts of noise caused by sudden temperature changes, the droning fan of a central-air system, or the sizzling of a dusty element.

when you purchase or install a heater in a home, you should establish a heat distribution plan to evaluate the heating requirement of each room or area of the home. Installing heat sources at several strategic points prevents the overheating of one single unit as it tries to keep up with demand for the whole room. When the heaters are placed at the right spots around the room, the result is maximum comfort and complete safety. Would you like us to plan your ideal heating plan? Contact the team of Convectair experts. This service is free, and it could save you a bundle! 1 800 463-6478 / support@convectair.ca

Do a heat loss calculation on-line now!

When convection heaters on the same floor are not set to the same degree of heating comfort, the door to each room should be closed. In doing so, you’ll prevent overburdening a few units with the task of heating a cool air mass from neighbouring rooms.

Convectairs for the bathroom are designed to withstand splashes. The bigger models feature a control panel that is easy to access but safely out of children’s reach. The smaller units and the convection heaters have a panel that can be made tamper-proof. And all the fans (except the one of the Soprano) operate on a timer, so that the heater can’t be left on by mistake.

Convectair heating units meet Canadian and American safety standards . In addition, their designs are based on the more stringent performance standards applied in Europe.

• 2 years against all defects
• 5 years on heating elements

Once the guarantee expires, the Convectair technical team is a reliable source of advice and service. Even 20 years after purchase, a Convectair unit can be repaired and refurbished.

Consult here a list of our authorized Service Centers

For guaranteed, dependendable operation, we recommend that all units be installed by a licensed electrical contractor.